Schedule: Mill Design - Introduction to Engineering Design | | | | Start 1st Quarter - (47 Days) |
| | | | | | | | | End 1st 9 weeks | |
Assignment | | | | | | Due Date | | | | | | | |
| | | | | | | | | Start 2nd Quarter (44 Days) |
Module 1: Getting Started | | | | | Due Date | | End 2nd 9 weeks | | |
| | | | | | | | | | | | | | |
| Pre-Quiz | | | | | | | | Start 3rd Quarter (43 Days) |
| | | | | | | | | End 3rd 9 weeks | | |
| Lesson 1: Before You Begin | | | | | | | | | | | |
| Lesson 2: Mastercam Interface | | | | | | Start 4th Quarter (44 Days) | |
| Lesson 3: AutoCursor | | | | | | Last Day for Work to be turned in |
| Lesson 4: General Selection | | | | | | | | | | | |
| Lesson 5: Function Bars | | | | | | | | | | | |
| Lesson 6: Setup and Geometry | | | | | | | | | | | |
| | | | | | | | | | | | | | |
| Quiz | | | | | | | | | | | | | |
| | | | | | | | | | | | | | |
Module 2: Mill Design | | | | | Due Date | | | | | | | |
| | | | | | | | | | | | | | |
| Pre-Quiz | | | | | | | | | | | | | |
| | | | | | | | | | | | | | |
| Lesson 1: Geometry Overview | | | | | | | | | | | |
| Lesson 2: Part 1: Start and End Points | | | | | | | | | | |
| Lesson 3: Part 2: Geometry Offset | | | | | | | | | | |
| Lesson 4: Part 2: Translate | | | | | | | | | | | |
| Lesson 5: Part 2: Solid | | | | | | | | | | | |
| Lesson 6: Part 3: Angle and Extrude | | | | | | | | | | |
| Lesson 7: Part 3: Solid | | | | | | End 1st 9 weeks | |
| Lesson 8: WCS and Planes | | | | | | | | | | | |
| Lesson 9: Part 4: Work Coordinate System | | | | | | | | | | |
| Lesson 10: Part 5: 2D and 3D | | | | | | | | | | | |
| Lesson 11: Bike Brake | | | | | | | | | | | |
| Lesson 12: Bike Fork | | | | | | | | | | | | |
| Lesson 13: Connect Six | | | | | | | | | | | |
| Lesson 14: Soccer Ball | | | | | | | | | | | |
| | | | | | | | | | | | | | |
Module 3: Mill Toolpath | | | | | | | Start 2nd Quarter (44 Days) |
| | | | | | | | | | | | | | |
| Lesson 1: Chaining | | | | | | | | | | | | |
| Lesson 2: Toolpath Overview | | | | | | | | | | | |
| Lesson 3: Part 1 | | | | | | | | | | | | |
| Lesson 4: Part 1 Cut Outside | | | | | | | | | | | |
| Lesson 5: Part 2 | | | | | | | | | | | | |
| Lesson 6: Part 3 Setup 1 | | | | | | | | | | | |
| Lesson 7: Part 3 Setup 2 | | | | | | End 2nd 9 weeks | | |
| Lesson 8: Part 4 Self Test | | | | | | | | | | | |
| Lesson 9: Part 4 1st Setup | | | | | | | | | | | |
| Lesson 10: Part 4 2nd Setup | | | | | | | | | | | |
| Lesson 11: Part 4 3rd Setup | | | | | | | | | | | |
| Lesson 12: Part 4 Verify | | | | | | | | | | | |
| Lesson 13: Part 6 | | | | | | | | | | | | |
| Lesson 14: Part 6 Standard Pocket | | | | | | | | | | |
| Lesson 15: Part 6 View Sheets | | | | | | | | | | | |
| Lesson 16: Part 6 Open Pockets | | | | | | | | | | | |
| Lesson 17: Part 6 Pocket Island Facing | | | | | | | | | | |
| Lesson 18: Part 6 Pocket Remachining | | | | | | | | | | |
| Lesson 19: Part 6 Multi Height Islands | | | | | | | | | | |
| Lesson 20: Part 7 | | | | | | | | | | | | |
| Lesson 21: Additional Toolpath | | | | | | | | | | | |
| Lesson 22: Challenge Project | | | | | | | | | | | |
| | | | | | | | | | | | | | |
Module 4: 2D High Speed Toolpath | | | | | | | | | | | |
| | | | | | | | | | | | | | |
| Lesson 1: Core Mill | | | | | | | | | | | |
| Lesson 2: Peel Mill | | | | | | | | | | | |
| Lesson 3: Blend Mill | | | | | | | | | | | |
| Lesson 4: Area Mill | | | | | | | | | | | |
| Lesson 5: Rest Mill | | | | | | | | | | | |
| Lesson 6: Dynamic Mill | | | | | | | | | | | |
| | | | | | | | | | | | | | |